U-Boot 2015.01-Vienna-SDK-2.5-4 (Apr 15 2024 - 10:41:23) I2C: ready SPI: ready DRAM: 256 MiB WARNING: Caches not enabled NAND: SPI NAND: Got idcode c2 26 03 00 c2. SN: Detected MX35LF2GE4AD with page size 2048, total 256 MiB 256 MiB MMC: MMC Version 2.90a VPL DWMMC: 0 In: serial Out: serial Err: serial Model: Schubert Loader: Version 0x23063001 @ 0x81005fe0 Relocation Offset is: 03f2c000 Relocating to 03f2e000, new gd at 03a1def0, sp at 03a1ded0 Net: GMAC Desc/Buf : 0x03ff3e00 -> 0x04000000 Phy 1 not found PHY reset timed out [GMAC] Fatal Error: Reset GMAC timeout, not complete over 1sec PHY TYPE : Generic PHY(rgmii) Link Detect : Link Status : Link Up : Full Duplex Link Speed : 1000Mbps dweqos Hit any key to stop autoboot: 0 NAND read: device 0 offset 0x1e0000, size 0x400000 4194304 bytes read: OK NAND read: device 0 offset 0x180000, size 0x60000 393216 bytes read: OK Kernel image @ 0xa00000 [ 0x000000 - 0x3b54c8 ] ## Flattened Device Tree blob at 01400000 Booting using the fdt blob at 0x1400000 Using Device Tree in place at 01400000, end 0140a23f Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 4.9.0-1 (koobiss@Virtualbox) (gcc version 4.9.4 (Buildroot 2017.02.11) ) #1 4.9.257-Vienna-SDK-2.5-8-1 2024. 0 5. 29. (수) 00:57:17 KST CPU: ARMv7 Processor [410fc051] revision 1 (ARMv7), cr=10c53c7d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache OF: fdt:Machine model: Vienna SoC Memory policy: Data cache writeback CPU: All CPU(s) started in SVC mode. Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15488 Kernel command line: root=/dev/mtdblock4 mem=16M@0x00000000 mem=45M@0x1300000 console=0,115200 phy_mode=rgmii PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 54080K/62464K available (5548K kernel code, 206K rwdata, 1352K rodata, 176K init, 149K bss, 8384K reserved, 0K cma-r eserved) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xffc00000 - 0xfff00000 (3072 kB) vmalloc : 0xc4800000 - 0xff800000 ( 944 MB) lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0573438 (5550 kB) .init : 0xc06f2000 - 0xc071e000 ( 176 kB) .data : 0xc071e000 - 0xc0751a78 ( 207 kB) .bss : 0xc0751a78 - 0xc0776f98 ( 150 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:16 nr_irqs:16 16 sched_clock: 64 bits at 150MHz, resolution 6ns, wraps every 2199023255551ns clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x2298375bd0, max_idle_ns: 440795208267 ns Switching to timer-based delay loop, resolution 6ns Console: colour dummy device 80x30 Calibrating delay loop (skipped), value calculated using timer frequency.. 300.00 BogoMIPS (lpj=1500000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok Setting up static identity map for 0x8240 - 0x8298 devtmpfs: initialized VFP support v0.3: implementor 41 architecture 2 part 30 variant 5 rev 1 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes) pinctrl core: initialized pinctrl subsystem NET: Registered protocol family 16 DMA: preallocated 256 KiB pool for atomic coherent allocations remap 16M to 0xc4880000 hw-breakpoint: found 2 (+1 reserved) breakpoint and 1 watchpoint registers. hw-breakpoint: maximum watchpoint size is 4 bytes. irq: no irq domain found for /soc/vpl-gpio@b3600000 ! apb_dmac b4100000.vpl_apbcdma: APBC DMA Controller, 16 channels SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb i2c_designware b2d00000.i2c: tx_fifo_depth [16] rx_fifo_depth [16] giuliani 0-005c: giu-dummy giuliani 0-005d: giu-dummy i2c_designware b2e00000.i2c: tx_fifo_depth [16] rx_fifo_depth [16] i2c_designware b2f00000.i2c: tx_fifo_depth [16] rx_fifo_depth [16] Linux video capture interface: v2.00 pps_core: LinuxPPS API ver. 1 registered pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti PTP clock support registered Advanced Linux Sound Architecture Driver Initialized. clocksource: Switched to clocksource arm_global_timer NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 0, 4096 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. hw perfevents: enabled with armv7_cortex_a5 PMU driver, 3 counters available workingset: timestamp_bits=30 max_order=14 bucket_order=0 squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 5 ports, IRQ sharing disabled console [ttyS0] disabled b2700000.serial: ttyS0 at MMIO 0xb2700004 (irq = 20, base_baud = 12499999) is a 16550A console [ttyS0] enabled b3b00000.serial: ttyS2 at MMIO 0xb3b00004 (irq = 21, base_baud = 1200000) is a 16550A b3c00000.serial: ttyS3 at MMIO 0xb3c00004 (irq = 22, base_baud = 1200000) is a 16550A b3d00000.serial: ttyS4 at MMIO 0xb3d00004 (irq = 23, base_baud = 1200000) is a 16550A Remapped base address = 0xC486F000 Remapped base address = 0xC4871000 brd: module loaded pmc version:0x03000001 rtcc version:0x02010000 giu-rtcc giu-rtcc: rtc core: registered giu-rtcc as rtc0 gpadc version:0x02000000 spi dma init OK nand: device found, Manufacturer ID: 0xc2, Chip ID: 0x26 nand: Macronix MXIC MX35LF2GE4AD 2G 3.3V SPI nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 6 ofpart partitions found on MTD device spi0.0 Creating 6 MTD partitions on "spi0.0": 0x000000000000-0x000000140000 : "nand-bootldr" 0x000000140000-0x000000180000 : "nand-env" 0x000000180000-0x0000001e0000 : "nand-dtb" 0x0000001e0000-0x0000005e0000 : "nand-kernel" 0x0000005e0000-0x0000015e0000 : "nand-rootfs" 0x0000015e0000-0x000008000000 : "nand-ubifs" libphy: Fixed MDIO Bus: probed GMAC: PHY mode is rgmii stmmac - user ID: 0x10, Synopsys ID: 0x42 RX Checksum Offload Engine supported TX Checksum insertion supported clk rate 249999999 eth0 - (dev. name: bc200000.dw_eqos - id: -1, IRQ #0 IO base addr: 0xc4908000) libphy: dweqos_mdio: probed dweqos bc200000.dw_eqos eth0: No PHY found dweqos bc200000.dw_eqos eth0: Failed to probe MDIO bus usbcore: registered new interface driver r8152 usbcore: registered new interface driver asix vatics-usb2phy b3100000.usbphy: regs c487e000 vatics-usb2phy b3100000.usbphy: version 12000001 vatics-usb2phy b3100000.usbphy: USB PHY ctrl0 = 0xbf19a6db, ctrl1 = 0xff00, counter = 0x2e0 dwc2 b8300000.dwc2: Specified GNPTXFDEP=256 > 32 dwc2 b8300000.dwc2: EPs: 7, dedicated fifos, 1992 entries in SPRAM dwc2 b8300000.dwc2: DWC OTG Controller dwc2 b8300000.dwc2: new USB bus registered, assigned bus number 1 dwc2 b8300000.dwc2: irq 34, io mem 0x00000000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usbcore: registered new interface driver usb-storage i2c /dev entries driver usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) GIC: PPI14 is secure or misconfigured GIC: PPI14 is secure or misconfigured mpcore_wdt b1f00600.watchdog: MPcore Watchdog Timer: 0.1. mpcore_noboot=0 mpcore_margin=60 sec (nowayout= 0) Synopsys Designware Multimedia Card Interface Driver dwmmc_vienna b8100000.dwmmc0: using uhs-gpio:35 request duplicate pin 35(UARTC_2_OB_SDA) please check!!! vienna-pinctrl vienna-pinmux: request() failed for pin 35 vienna-pinctrl vienna-pinmux: pin-35 (Vienna-default-pin:35) status -16 dwmmc_vienna b8100000.dwmmc0: dev-id: 0 dwmmc_vienna b8100000.dwmmc0: IDMAC supports 32-bit address mode. dwmmc_vienna b8100000.dwmmc0: Using internal DMA controller. dwmmc_vienna b8100000.dwmmc0: Version ID is 290a dwmmc_vienna b8100000.dwmmc0: DW MMC controller at irq 27,32 bit host data width,128 deep fifo vienna_set_mmc_clock: clk name vpl_mshc0_clk, set bus_hz 50000000, div 00008180 val c3419aa0 mmc_host mmc0: uhs-gpio:35, voltage:v330 mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63) dwmmc_vienna b8100000.dwmmc0: 1 slots initialized dwmmc_vienna b8100000.dwmmc0: Tuning high-speed card enabled. ledtrig-cpu: registered to indicate activity on CPUs usbcore: registered new interface driver usbhid usbhid: USB HID core driver acdc version:0x02000000 soc-audio soc-audio.0: ASoC: machine Vatics_evm should use snd_soc_register_card() soc-audio soc-audio.0: giu-hifi <-> vatics-pcm mapping ok NET: Registered protocol family 10 sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver NET: Registered protocol family 17 8021q: 802.1Q VLAN Support v1.8 input: power_gpio as /devices/virtual/input/input0 random: fast init done giu-rtcc giu-rtcc: setting system clock to 1970-01-01 00:35:11 UTC (2111) ALSA device list: #0: Vatics_evm ttyS0 - Setup RX Timeout 706 VFS: Mounted root (squashfs filesystem) readonly on device 31:4. devtmpfs: mounted Freeing unused kernel memory: 176K This architecture does not have kernel memory protection. usb 1-1: new high-speed USB device number 2 using dwc2 random: init: uninitialized urandom read (4 bytes read) random: mount: uninitialized urandom read (4 bytes read) random: mkdir: uninitialized urandom read (4 bytes read) Starting logging: OK Starting mdev... usb 1-1: reset high-speed USB device number 2 using dwc2 r8152 1-1:1.0 eth0: v1.08.9 read-only file system detected...done Starting network: OK Starting network by U-Boot settings2: IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready ubi0: attaching mtd5 r8152 1-1:1.0 eth0: carrier on IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready random: crng init done random: 7 urandom warning(s) missed due to ratelimiting ubi0: scanning is finished ubi0: attached mtd5 (name "nand-ubifs", size 106 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 849, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 3387286245 ubi0: available PEBs: 61, total reserved PEBs: 788, PEBs reserved for bad PEB handling: 40 ubi0: background thread "ubi_bgt0d" started, PID 112 ubi0 error: ubi_create_volume: volume "ubi0_0" exists (ID 0) ubi0 error: ubi_create_volume: cannot create volume 1, error -17 UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 116 UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "ubi0_0" UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS (ubi0:0): FS size: 93073408 bytes (88 MiB, 733 LEBs), journal size 4698112 bytes (4 MiB, 37 LEBs) UBIFS (ubi0:0): reserved for root: 4396086 bytes (4293 KiB) UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 45E141E9-1C52-4F6B-B744-5C31F5279633, small LPT model Godshand: loading out-of-tree module taints kernel. VPL_EDMC: initialized (driver 6.3.0.2 HW 10.0.0.7) DRAM 0 base address = 0x04000000, size = 0x0C000000 Install VPL_DMAC 0 device driver version 2.0.0.3 on VPL_DMAC 0 hardware version 14.0.0.0 complete !! Install VPL_DMAC 1 device driver version 2.0.0.3 on VPL_DMAC 1 hardware version 14.0.0.0 complete !! VMA_IFPE: Install VMA_IFPE device driver version 1.1.0.0 on VMA_IFPE hardware version 6.0.0.0 complete !! Install VMA_JDBE device driver version 2.0.0.1 on VMA_JDBE hardware version 6.0.0.0 complete !! Install VMA_JEBE device driver version 2.0.0.1 on VMA_JEBE hardware version 12.0.0.0 complete !! Install VMA_ISPE device driver version 2.0.0.5 on VMA_ISPE hardware version 11.0.0.0 complete !! Install VMA_H4CDE device driver version 2.0.0.8 on VMA_H4EE hardware version 8.0.0.0 complete !! Install VMA_MEAE device driver version 2.0.0.0 on VMA_MEAE hardware version 10.0.0.0 complete !! Install VMA_RS device driver version 2.0.0.4 on VMA_ISPE hardware version 11.0.0.0 complete !! Install VMA_DCE device driver version 2.0.0.4 on VMA_DCE hardware version 9.1.0.1 complete !! usb_f_fs: exports duplicate symbol ffs_lock (owned by kernel) usb_f_fs: exports duplicate symbol ffs_lock (owned by kernel) insmod: can't insert 'usb_f_fs.ko': invalid module format g_webcam gadget: uvc_function_bind CHRDEV "uac" major number 233 goes below the dynamic allocation range g_webcam gadget: Webcam Video Gadget g_webcam gadget: g_webcam ready dwc2 b8300000.dwc2: bound driver g_webcam RTW: module init start RTW: rtl8192eu v5.11.2-6-g17aaefb.20200723_COEX20171113-0047 RTW: build time: Nov 4 2023 15:46:49 RTW: rtl8192eu BT-Coex version = COEX20171113-0047 RTW: rtw_inetaddr_notifier_register usbcore: registered new interface driver rtl8192eu RTW: module init ret=0 CHRDEV "vma_h5cde" major number 232 goes below the dynamic allocation range register_chrdev done !! Got major number 0 !! chown: unknown group CHRDEV "vpl_vic" major number 231 goes below the dynamic allocation range Install VPL_VIC device driver version 6.0.0.13 on VPL_VIC hardware version 8.0.0.0 complete !! [TP2825]: driver version 0.0.0.0 for device 0 insmod success. # [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! video track0 use mechanism: sharedbuffer video track0 path: venc_srb_1 video track0 cmd fifo: /tmp/venc/c0/command.fifo@0 video track1 use mechanism: sharedbuffer video track1 path: venc_srb_2 video track1 cmd fifo: /tmp/venc/c0/command.fifo@1 audio track0 use mechanism: sharedbuffer audio track0 path: aenc_srb_1 audio track0 cmd fifo: /tmp/aenc/c0/command.fifo audio back channel track0 use mechanism: sharedbuffer audio back channel track0 path: audio_backchannel_srb_1 audio back channel track0: payload type = 0, encoding name = PCMU, clock rate = 8000, channels = 1 audio back channel track1 use mechanism: sharedbuffer audio back channel track1 path: audio_backchannel_srb_2 audio back channel track1: payload type = 99, encoding name = G726-32, clock rate = 8000, channels = 1 stream0 access file: live1.sdp, video track 0, audio track -1, mdata track -1, audio back channel -1 multicst ip (null), ttl 0, video port 0, audio port 0, mdata port 0 stream1 access file: live2.sdp, video track 1, audio track -1, mdata track -1, audio back channel -1 multicst ip (null), ttl 0, video port 0, audio port 0, mdata port 0 [RtspServer] listen port is 554 [RtspServer] rtp start port is 8888 [RtspServer] fdipc path is /tmp/rtspsrv_fdipc.sck [RtspServer] authenticate mode is none [RtspServer] connection timeout is 60 (10 to 300) [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! ********************************************************** KnDMAC 1 virq = 38 eron Firmware Ver. 1.2.0.1204 Build Time: Oct 17 2024 05:47:14 ********************************************************** HOST STREAM mode iniparser_load ./ini/host_stream.ini [NNM] sensor_cfg: ./Resource/VIC/0/tp2825_1920x1080_ch0.cfg autoscene_config: (null) [NNM] fec_calibrate: ./ini/fec_calibrate.ini fec_conf: ./ini/fec_conf.ini [NNM] Model: nef/models_630_LR_1008_v2.nef ImageWidth: 128 ImageHeight: 128 Threshold: 0.500000 Fps: 25.000000 [NNM] Model: nef/models_630_LR_1008_v2.nef dwModelId: 35000 dwJobId: 3002 [main] app_initialize >> Start running KL630 KDP2 HOST_STREAM mode ... starting KDP2 middleware ... Start to use mass memory access library version 3.0.0.7 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open DMAC device driver version 2.0.0.3 successful !! mdl_parser_open(): fw parser hdl=0x0x31650 =================== Reset IE Parser NEF info =================== Model Amount : 1 [0] Models ID : 35000 [0] Models Version: 0x1 [0] Command.bin Length : 2040 [0] Command.bin Buffer Virtual Address : 0x500042c0 [0] Weight.bin Length : 2109488 [0] Weight.bin Buffer Virtual Address : 0x50004ac0 [0] Setup.bin Length : 79688 [0] Setup.bin Buffer Virtual Address : 0x50207af0 [0] Working Buffer Length : 3735552 [0] Working Buffer Virtual Address : 0x5021c400 [0] Output Buffer Length : 64 [0] Input Buffer Length : 737280 [0] [dim] Input 0 Row: 128 [0] [dim] Input 0 Col: 128 [0] [dim] Input 0 Channel: 3 [0] [postproc] Output num: 1 ======================================================== VMTK_IE_Init(): IE Version. 0x0001 VMTK_NPU_Init(): NPU Version. 0x0001 allocating memory for fifoq: image 3 x 32768, result 3 x 524288, total 1671168 bytes Number of valid nodes: 64 [init_video_source] Normal Mode ===== Vienna SDK version: 2.5.5 ===== Start to use mass memory access library version 3.0.0.7 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open DMAC device driver version 2.0.0.3 successful !! I/[VMTK_VI] VMTK_VI_Init D/[VMTK_VI] allocate yuv buff 0 bytes Start to use VideoCap library version 6.1.0.0 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open vpl_vic device driver version 6.0.0.13 successful !! D/[VMF_VSRC] [setup_ifp_id] dwIndex:0, interface:0 D/[VMF_VSRC] ifp_init_handle(): IFP PQ folder: ./Resource/IFPE/0/ D/[VMTK_IFPE] VMTK_IFP_Init(): max w:1920, h:1080, input w:1920, h:1080, oh: 1080, fmt:12 Start to use IFPE library version 5.3.0.3 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [VSABuffMgr][Info]:Initail on version v1.0.0.10-0-g0889a2c Open IFPE device driver version 1.1.0.0 successful! D/[VMTK_IFPE] ifp_init_output_buffers(): dwCplxMapStride(128), dwCplxMapSize(8704) dwCplxMapOffset(0). D/[VMTK_IFPE] ifp_init_output_buffers(): dwMrfMapStride(256), dwMrfMapSize(34560), dwMrfMapOffset(0). D/[VMF_VSRC] [setup_ifp_map_info] ptStats->dwTotalMapSize:21504 D/[VMF_VSRC] VSRC_IFP_Init_Normal():vsrc_ssm_ifp_0 max buffer size:3 ring size:0 ysize:1671168, cplx:8704, mrf:34560 st:1536 D/[VMF_VSRC] VSRC_SetupIfpStatisMap(): IFP stats map ssm:vsrc_ssm_ifp_0_statis init 21504! D/[VMF_VSRC] init_duplex_ctx() 1920,1080,1536 ./Resource/ISP/0/ [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [VSABuffMgr][Info]:Initail on version v1.0.0.10-0-g0889a2c D/[VMTK_ISPE] isp_setup_map_info(): set isp cplx out frame w 0 h 0 st 0 D/[VMTK_ISPE] isp_setup_map_info(): set isp mrf out frame w 0 h 0 st 0 D/[VMTK_ISPE] isp_setup_map_info(): set isp cplx out frame w 0 h 0 st 0 D/[VMTK_ISPE] isp_setup_map_info(): set isp mrf out frame w 0 h 0 st 0 D/[VMF_VSRC] init_ifp_stream(): init ifp stream. I/[VMTK_VI] VMTK_VI_Start [setup_fec_mode] FEC MODE: FEC_MODE_ORIGINAL D/[FEC_LYT] IFP output w:1920, h:1080, st:1536, color:0, FEC output w:1920, h:1080, st:1920 D/[VMF_VSRC] VMF_VSRC_SetOutput(), ptConfig->tLayout: dwCanvasWidth(1920), dwCanvasHeight(1080), dwVideoWidth(1920), dwVideo Height(1080), dwVideoPosX(0), dwVideoPosY(0). D/[VMF_VSRC] VSRC_Stream_Init(): vsrc stream ysize:2088960 w:1920, st:1920, h:1080 D/[VMF_VSRC] setup_stream_extra_map(): cplx st:128, size:8704. D/[VMF_VSRC] setup_stream_extra_map(): mrf st:240, size:32400. Start to use mass memory access library version 3.0.0.7 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open DMAC device driver version 2.0.0.3 successful !! D/[VMF_VSRC] VSRC_ISP_InitHandle() 1920,1080,1536 ./Resource/ISP/0/ [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [VSABuffMgr][Info]:Initail on version v1.0.0.10-0-g0889a2c D/[VMTK_ISPE] init_isp_cplx_frame_info(): isp input cplx frame info st: 128,w: 120, h: 68 D/[VMTK_ISPE] init_isp_cplx_frame_info(): isp output cplx frame info DMAC 0 virq = 37 st: 128,w: 120, h: 68 D/[VMTK_ISPE] init_mrf_frame_info(): isp input mrf frame info st: 256,w: 240, h: 135 D/[VMTK_ISPE] init_mrf_frame_info(): isp output mrf frame info st: 240,w: 240, h: 135 D/[VMF_VSRC] VSRC_Stream_InitIsp(): isp out st:1920, w:1920, h:1080 D/[VMTK_ISPE] isp_setup_map_info(): set isp cplx out frame w 120 h 68 st 96 D/[VMTK_ISPE] isp_setup_map_info(): set isp mrf out frame w 240 h 135 st 192 D/[VMTK_ISPE] isp_setup_map_info(): set isp cplx out frame w 120 h 68 st 128 D/[VMTK_ISPE] isp_setup_map_info(): set isp mrf out frame w 240 h 135 st 240 D/[VSRC_AES] VSRC_AES_GetViBuffer(): get vi buffer failed: 801C000B. D/[VSRC_AES] VSRC_AES_GetViBuffer(): get vi buffer failed: 801C000B. Inference: (128,128) DrawScreen: (1920, 1080) Resize: (128, 128) Ratio: (0.067, 0.119) [init_video_encoder] enc :1920, 1080 D/[VBIND] VMF_BIND_Request() src status:3, is_request_resize:0, src_width:1920, src_height: 1080, src_stride: 1920, dwWidth: 1920, dwHeight: 1080, dwOldResolutionWidth(0), dwOldResolutionHeight(0) D/[VBIND] VMF_BIND_Request() req_w:1920, req_h:1080, req_st:1920 src_pin:vsrc_ssm_0 cr:0 D/[VMF_VENC] VENC_CTX_Init() cr(0), st(1920), h(1080) pin name vsrc_ssm_0. [JPEGEnc][Info]: Start to use JPEGEnc library version 2.1.0.0 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [JPEGEnc][Info]: Open JEBE device driver version 2.0.0.1 successful !! D/[VMTK_JE] VMTK_JE_Init(): Initialized VML JPEG encoder object 0x00082f88 Start to use mass memory access library version 3.0.0.7 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open DMAC device driver version 2.0.0.3 successful !! D/[VMF_VENC] venc_mgr_find_venc() Venc not found, venc num(0) D/[VMF_VENC] venc_mgr_add_venc() Venc added, venc num(1) D/[VMTK_JE] VMTK_JE_SetOptions(): eOptionFlag 0x0000002c. [init_video_encoder] enc :128, 128 D/[VBIND] VMF_BIND_Request() src status:3, is_request_resize:1, src_width:1920, src_height: 1080, src_stride: 1920, dwWidth: 128, dwHeight: 128, dwOldResolutionWidth(0), dwOldResolutionHeight(0) D/[VBIND] do_resize() rs_idx=0, w=128, h=128, st:128, x:0 Rsindex: 0, KeepRatio: 0 D/[VMF_VSRC] VSRC_SSM_SetColor() dwWidth:128, dwHeight:128, dwStride:128 D/[MEMSET_2D] [VMF_MEMSET_2D_Process] Width: 128, Height: 128, Stride: 128 D/[VMF_VSRC] VSRC_SSM_SetColor() dwWidth:128, dwHeight:128, dwStride:128 D/[MEMSET_2D] [VMF_MEMSET_2D_Process] Width: 128, Height: 128, Stride: 128 D/[VMF_VSRC] setup_resize_ssm(): SSM_Writer_Init resize: [vsrc_ssm_0_128_128], RS 0 color: -2139095039 D/[VBIND] VMF_BIND_Request() req_w:128, req_h:128, req_st:128 src_pin:vsrc_ssm_0_128_128 cr:0 D/[VMF_VENC] VENC_CTX_Init() cr(0), st(128), h(128) pin name vsrc_ssm_0_128_128. D/[VMTK_H4E] VMTK_H4E_Init():ptHandle->dwYOffset_:0 ptHandle->dwUvOffset_:0 D/[VMTK_H4E] [VMTK_H4E_Init] tVmlInitOpt.dwTicksPerSecond: 30000 Start to use H264Enc library version 7.3.0.1 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open H4EE device driver version 2.0.0.8 successful !! D/[VMTK_H4E] Initialized VML H.264 encoder object 0x000846c0 D/[VMTK_H4E] [h4e_config] H264 time scale: 30000 Start to use mass memory access library version 3.0.0.7 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open DMAC device driver version 2.0.0.3 successful !! D/[VMF_VENC] venc_mgr_find_venc() Venc not found, venc num(1) D/[VMF_VENC] venc_mgr_add_venc() Venc added, venc num(2) D/[VMTK_H4E] VMTK_H4E_SetOptions eOptionFlag 0x00000011 D/[VMTK_H4E] VMTK_H4E_SetOptions eOptionFlag 0x00000012 initial parameter set length is 40 sps:Z2RACqwsaggRJuCgwKgAAB9AAAOphN9Q pps:aO4fLA== [init_video_encoder] enc :640, 480 D/[VBIND] [VMF_BIND_CheckResize] check resize size ret value 0. D/[VBIND] VMF_BIND_Request() src status:3, is_request_resize:1, src_width:1920, src_height: 1080, src_stride: 1920, dwWidth: 640, dwHeight: 480, dwOldResolutionWidth(0), dwOldResolutionHeight(0) D/[VBIND] do_resize() rs_idx=0, w=128, h=128, st:128, x:0 Rsindex: 0, KeepRatio: 0 D/[VBIND] do_resize() rs_idx=1, w=640, h=480, st:640, x:0 Rsindex: 0, KeepRatio: 0 D/[VMF_VSRC] VSRC_SSM_SetColor() dwWidth:640, dwHeight:480, dwStride:640 D/[MEMSET_2D] [VMF_MEMSET_2D_Process] Width: 640, Height: 480, Stride: 640 D/[VMF_VSRC] VSRC_SSM_SetColor() dwWidth:640, dwHeight:480, dwStride:640 D/[MEMSET_2D] [VMF_MEMSET_2D_Process] Width: 640, Height: 480, Stride: 640 D/[VMF_VSRC] setup_resize_ssm(): SSM_Writer_Init resize: [vsrc_ssm_0_640_480], RS 1 color: -2139095039 D/[VBIND] VMF_BIND_Request() req_w:640, req_h:480, req_st:640 src_pin:vsrc_ssm_0_640_480 cr:0 D/[VMF_VENC] VENC_CTX_Init() cr(0), st(640), h(480) pin name vsrc_ssm_0_640_480. D/[VMTK_H4E] VMTK_H4E_Init():ptHandle->dwYOffset_:0 ptHandle->dwUvOffset_:0 D/[VMTK_H4E] [VMTK_H4E_Init] tVmlInitOpt.dwTicksPerSecond: 50000 Start to use H264Enc library version 7.3.0.1 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open H4EE device driver version 2.0.0.8 successful !! D/[VMTK_H4E] Initialized VML H.264 encoder object 0x000a6228 D/[VMTK_H4E] [h4e_config] H264 time scale: 50000 Start to use mass memory access library version 3.0.0.7 !! [MemMgr][Info]: Start to use memory manager library version 4.2.0.0 !! [MemMgr][Info]: Open EDMC device driver version 6.3.0.2 successful !! Open DMAC device driver version 2.0.0.3 successful !! D/[VMF_VENC] venc_mgr_find_venc() Venc not found, venc num(2) D/[VMF_VENC] venc_mgr_add_venc() Venc added, venc num(3) D/[VMTK_H4E] VMTK_H4E_SetOptions eOptionFlag 0x00000011 D/[VMTK_H4E] VMTK_H4E_SetOptions eOptionFlag 0x00000012 [app_header_send_inference] Error: Job ID 3002 [kdp2_host_stream_image_thread] Error: callback function error (100) D/[VMF_VENC] venc_mgr_remove_venc() Venc removed, venc num(2) D/[VBIND] VMF_BIND_Request() src status:3, is_request_resize:0, src_width:1920, src_height: 1080, src_stride: 1920, dwWidth: 1920, dwHeight: 1080, dwOldResolutionWidth(0), dwOldResolutionHeight(0) D/[VMF_VENC] venc_mgr_remove_venc() Venc removed, venc num(1) D/[VBIND] VMF_BIND_Request() src status:3, is_request_resize:1, src_width:1920, src_height: 1080, src_stride: 1920, dwWidth: 128, dwHeight: 128, dwOldResolutionWidth(0), dwOldResolutionHeight(0) D/[VBIND] setup_resize_info()::76, found ptRsInfo->adwWidth[0] = 128, ptRsInfo->adwHeight[0] = 128, KeepRatio: 0 D/[VBIND] setup_resize_info()::216, unregistering 0 - ptRsInfo->adwWidth[0] = 128, ptRsInfo->adwHeight[0] = 128, ptRsInfo->d wChannelNum = 2 D/[VBIND] do_resize() rs_idx=0, w=640, h=480, st:640, x:0 Rsindex: 0, KeepRatio: 0 D/[VMTK_H4E] VMTK_H4E_ReleaseD/[VMF_VENC] venc_mgr_deref_vsrc() Vsrc removed, vsrc num(0) D/[VMF_VENC] venc_mgr_remove_venc() Venc removed, venc num(0) D/[VBIND] VMF_BIND_Request() src status:3, is_request_resize:1, src_width:1920, src_height: 1080, src_stride: 1920, dwWidth: 640, dwHeight: 480, dwOldResolutionWidth(0), dwOldResolutionHeight(0) D/[VBIND] setup_resize_info()::76, found ptRsInfo->adwWidth[1] = 640, ptRsInfo->adwHeight[1] = 480, KeepRatio: 0 D/[VBIND] setup_resize_info()::216, unregistering 1 - ptRsInfo->adwWidth[1] = 640, ptRsInfo->adwHeight[1] = 480, ptRsInfo->d wChannelNum = 1 D/[VMTK_H4E] VMTK_H4E_ReleaseI/[VMTK_VI] VMTK_VI_Stop W/[VMF_ISP_MD] VSRC_ISP_MD_Release() invalid input: VMF_VSRC_STREAM_OUTPUT_T is NULL. W/[VMF_ISP_MD] VSRC_ISP_MD_Release() invalid input: VMF_VSRC_STREAM_OUTPUT_T is NULL. W/[VMF_ISP_MD] VSRC_ISP_MD_Release() invalid input: VMF_VSRC_STREAM_OUTPUT_T is NULL. I/[VMTK_VI] VMTK_VI_Release VideoCap release done !!